Zebra ZT210 Bedienungsanleitung Seite 117
- Seite / 168
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
117
Routine Maintenance
Cleaning Schedule and Procedures
8/22/12 P1048261-004
3. Push down the peel-off mechanism release lever to open the peel assembly.
4. Remove any media liner to expose the pinch roller.
5. While manually rotating the pinch roller, clean it thoroughly with the swab from the
Preventive Maintenance Kit (part number 47362). In place of the Preventive Maintenance
Kit, you may use a clean swab dipped in a solution of isopropyl alcohol (minimum 90%)
and deionized water (maximum 10%). Allow the solvent to evaporate.
6. Use the swab to remove excess adhesive from the tear-off/peel-off bar. Allow the solvent
to evaporate.
7. Reload the media liner through the peel mechanism. For instructions, see Final Steps for
Peel-Off Mode (with or without Liner Take-Up) on page 68.
Important • Apply minimum force when cleaning the tear-off/peel-off bar. Excessive
force can cause the tear-off/peel-off bar to bend, which could have a negative effect on
peel performance.
- ZT210™/ZT220™/ZT230™ 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- HOME MENU 18
- SETTINGS 18
- ▼ XXXXXXX ▲ 19
- SETTINGS Menu 20
- SETTINGS Menu (continued) 21
- TOOLS Menu 24
- TOOLS Menu (continued) 25
- NETWORK Menu 28
- NETWORK Menu (continued) 29
- LANGUAGE Menu 32
- LANGUAGE Menu (continued) 33
- SENSORS Menu 34
- SENSORS Menu (continued) 35
- PORTS Menu 36
- PORTS Menu (continued) 37
- Types of Media 38
- Printer Setup and Operation 39
- Ribbon Overview 40
- Adhesive Test 41
- Ribbon Scratch Test 41
- Printer Setup and 43
- Operation 43
- Handling the Printer 44
- I) may damage the 46
- Data Cables 48
- 115 V AC 49
- 230 V AC 49
- Power Cord Specifications 50
- Select a Print Mode 52
- Load the Ribbon 55
- Printer Setup 56
- Load the Media 60
- Roll Media 61
- Fanfold Media 61
- Roll Media (Continued) 62
- Fanfold Media (Continued) 62
- If using… Then… 64
- Liner Take-Up) on page 68 65
- Mode on page 74 65
- Final Steps for Tear-Off Mode 66
- 11. Close the media door 67
- 23. Close the media door 73
- Final Steps for Cutter Mode 74
- 30. Close the media door 76
- Printer Configuration 77
- Changing Printer Settings 78
- Print Settings 79
- • THERMAL TRANS 80
- • DIRECT THERMAL 80
- • TEAR OFF 81
- • CUTTER 81
- Print Listings on Label 83
- Important • 87
- Directory Listing 88
- Network Settings 89
- Print Server Settings > 91
- Factory Print Server Settings 91
- Language Settings 92
- • ZPL II 94
- Sensor Settings 95
- Port Settings 96
- Serial Communications Setup 97
- MEDIA/RIBBON CAL 98
- LOAD BACKING 99
- REMOVE RIBBON 99
- Remove the ribbon (if used) 100
- CALIBRATING 101
- PLEASE WAIT 101
- RELOAD ALL 101
- CONTINUE 101
- Close the printhead 102
- Close the media door 102
- Reload the ribbon (if used) 102
- Adjust the Printhead Pressure 103
- If the media... Then 104
- Adjust Ribbon Tension 106
- Remove Used Ribbon 107
- Routine Maintenance 109
- Area Method Interval 110
- Printer Exterior 111
- Media Compartment and Sensors 111
- Raise the media door 113
- 8. Close the media door 115
- Clean the Peel Assembly 116
- Clean the Cutter Module 120
- Remove the cutter shield 121
- Replacing Printer Components 124
- Lubrication 124
- Troubleshooting 125
- Troubleshooting Checklist 126
- Meaning of Indicator Lights 127
- Printing Issues 129
- Ribbon Problems 132
- Error Messages 134
- RIBBON OUT 135
- PH NOT AUTHENTICATED 135
- REPLACE PRINTHEAD 135
- Display/ 137
- Indicator Lights 137
- Communications Problems 138
- Miscellaneous Issues 139
- Printer Diagnostics 141
- CANCEL Self Test 142
- PAUSE Self Test 143
- FEED Self Test 144
- Print Quality Description 145
- FEED + PAUSE Self Test 147
- CANCEL + PAUSE Self Test 147
- FE indicates a framing error 148
- PE indicates a parity error 148
- NE indicates noise 148
- Sensor Profile 149
- Specifications 151
- General Specifications 152
- Printing Specifications 153
- Ribbon Specifications 153
- Media Specifications 154
- Glossary 155
- 8/22/12 P1048261-004 159
- P1048261-004 8/22/12 160
- 8/22/12 P1048261-004 161
Verwandte Produkte und Handbücher für Etikettendrucker Zebra ZT210
Etikettendrucker Zebra Z4Mplus Bedienungsanleitung
(178 Seiten)
(178 Seiten)
Etikettendrucker Zebra QL+ Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Etikettendrucker Zebra PA400 Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Etikettendrucker Zebra Cameo Bedienungsanleitung
(22 Seiten)
(22 Seiten)
Etikettendrucker Zebra ZM400 Bedienungsanleitung
(33 Seiten)
(33 Seiten)
Etikettendrucker Zebra Z4M Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Etikettendrucker Zebra A100 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Etikettendrucker Zebra Z4M Bedienungsanleitung
(57 Seiten)
(57 Seiten)
Etikettendrucker Zebra 105SL Bedienungsanleitung
(130 Seiten)
(130 Seiten)
Etikettendrucker Zebra LI 72 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern