Zebra XiII-Series Bedienungsanleitung Seite 43
- Seite / 118
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Leaving the Program Mode
You can leave the Program Mode at any time by pressing the Setup/Exit
key. The SAVE CHANGES display will appear. There are five choices,
described below. Pressing the left or right black oval key displays other
choices and pressing the Next/Save key selects the displayed choice.
PERMANENT - permanently saves the changes. Values are stored in
the printer even when power is turned off.
TEMPORARY - saves the changes until changed again or until power
is turned off.
CANCEL - cancels all changes since pressing the Setup/Exit key except
the Darkness and Tear-Off settings (if they were changed).
LOAD DEFAULTS - loads factory defaults. The factory defaults are
shown on the following pages.
NOTE: Loading factory defaults will require ptinter calibration and
resetting the Head Resistor value.
LOAD LAST SAVE - loads values from the last Permanent Save.
Zebra XiII-Series User’s Guide 31
43
H:...Xi2UsersGuideR2.vp
Fri Aug 07 10:35:48 1998
Color profile: Disabled
Composite Default screen
- Zebra XiII-Series 1
- Fri Aug 07 08:59:37 1998 2
- Warranty Information 3
- Contents 5
- Operation 21 6
- Fri Aug 07 10:33:15 1998 7
- Options 71 8
- Specifications 77 8
- Appendix 87 9
- Glossary 99 9
- Index 103 9
- H:...Xi2UsersGuideR2.vp 10
- Fri Aug 07 10:33:16 1998 10
- Color profile: Disabled 10
- Composite Default screen 10
- List of Figures 11
- List of Tables 12
- Getting Started 13
- System Requirements 14
- Media and Ribbon Requirements 15
- Unpacking 15
- Fri Aug 07 10:34:39 1998 16
- Site Requirements 17
- Communications 18
- Loading Media 18
- Non-Continuous Media 19
- Continuous Media 19
- Black-Mark Media 19
- Tear-Off Mode Media Loading 20
- REWINDPEEL-OFF 21
- TEAR-OFF 21
- CUTTER REWIND 21
- BOTTOM SUPPLY REAR SUPPLY 22
- Continuous Media Loading 23
- Cutter Mode Media Loading 23
- Rewind Mode Media Loading 23
- Fri Aug 07 10:34:43 1998 24
- Peel-Off Mode Media Loading 26
- Transmissive Media Sensor 27
- Position Adjustment 27
- MEDIA SENSOR 28
- ADJUSTMENT 28
- Lower Media Sensor Adjustment 29
- STRIP OF MEDIA 30
- 6-12 INCHES LONG 30
- Fri Aug 07 10:34:46 1998 31
- Ribbon Removal 32
- Operation 33
- Peel-Off Mode 34
- Rewind Mode 34
- Cutter Mode 34
- Operator Controls 35
- Front Panel Display 36
- Front Panel Keys 37
- Front Panel Lights 38
- Printer Status Sensors 39
- Initial Printer Power-Up 40
- Configuration and Calibration 41
- Fri Aug 07 10:35:48 1998 42
- Leaving the Program Mode 43
- Fri Aug 07 10:35:49 1998 45
- Fri Aug 07 10:35:50 1998 50
- Fri Aug 07 10:35:51 1998 54
- Fri Aug 07 10:35:52 1998 57
- Sample ZPL II Label Formats 58
- Fri Aug 07 10:35:53 1998 62
- Routine Care and Adjustment 63
- Cleaning the Exterior 64
- Cleaning the Interior 64
- Cleaning the Sensors 65
- Lubrication 66
- Fuse Replacement 66
- Fri Aug 07 10:36:17 1998 67
- ADJUSTING 68
- AVAILABLE 68
- Printhead Pressure Adjustment 69
- Fri Aug 07 10:36:20 1998 70
- Fri Aug 07 10:36:37 1998 71
- Fri Aug 07 10:36:38 1998 72
- Printer Diagnostics 77
- Cancel Key Self Test 78
- Pause Key Self Test 79
- Feed Key Self Test 80
- Fri Aug 07 10:36:39 1998 81
- Fri Aug 07 10:36:40 1998 82
- Rewind Option 83
- Memory SIMMs 84
- On-Line Verifier 84
- Applicator Interface 85
- Media Supply Spindle 85
- Optional Media Supply Fins 85
- PCMCIA Type I Memory Cards 86
- KMT Printhead 86
- Communication Interfaces 86
- RS-485 Interface 87
- Fri Aug 07 10:36:58 1998 88
- Specifications 89
- Bar Codes 90
- General Specifications 91
- Printing Specifications 92
- Ribbon Specification 92
- Media Specifications 93
- Fri Aug 07 10:37:27 1998 94
- Standard 95
- Optional Printer Fonts 97
- @ABCDEFG 98
- Appendix 99
- Fri Aug 07 10:37:51 1998 100
- RS-232 Interconnections 101
- Fri Aug 07 10:37:52 1998 102
- Rear Panel DB-25S 103
- RS-422/RS-485 Connector 103
- Parallel Data Port 104
- Cabling Requirements 105
- ASCII Code Chart 106
- Fri Aug 07 10:37:54 1998 107
- Too Dark 108
- Slightly Dark 108
- Slightly Light 108
- Too Light 108
- “In-Spec” 108
- Figure 29. Bar Code Examples 109
- Fri Aug 07 10:37:57 1998 110
- Glossary 111
- Fri Aug 07 10:38:13 1998 112
- Fri Aug 07 10:38:14 1998 113
- Fri Aug 07 10:38:32 1998 115
Verwandte Produkte und Handbücher für Etikettendrucker Zebra XiII-Series
Etikettendrucker Zebra Z4M Bedienungsanleitung
(57 Seiten)
(57 Seiten)
Etikettendrucker Zebra 105SL Bedienungsanleitung
(130 Seiten)
(130 Seiten)
Etikettendrucker Zebra LI 72 Bedienungsanleitung
(62 Seiten)
(62 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.228 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern