Zebra 110Xi4 Betriebsanweisung Seite 102
- Seite / 188
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuration
Standard Control Panel Parameters
102
P1009874-003 Xi4™/RXi4™ User Guide 4/30/13
Set Control Prefix Character
The printer looks for this two-digit hex character to indicate the start of a
ZPL/ZPL II control instruction.
Note • Do not use the same hex value for the control, format, and
delimiter character. The printer must see different characters to
work properly.
Default Value: 7E ~
Range: 00 to FF
To change the value shown:
1. Press MINUS (-) to move to the next digit position.
2. Press PLUS (+) to increase the value of the digit.
Set Format Prefix Character
The format prefix is a two-digit hex value used as a parameter place marker
in ZPL/ZPL II format instructions. The printer looks for this hex character
to indicate the start of a ZPL/ZPL II format instruction. See the
Programming Guide for ZPL, ZBI, Set-Get-Do, Mirror, and WML for more
information.
Note • Do not use the same hex value for the control, format, and
delimiter character. The printer must see different characters to
work properly.
Default Value: 5E ^
Range: 00 to FF
To change the value shown:
1. Press MINUS (-) to move to the next digit position.
2. Press PLUS (+) to increase the value of the digit.
Set Delimiter Character
The delimiter character is a two-digit hex value used as a parameter place
marker in ZPL/ZPL II format instructions. See the Programming Guide for
ZPL, ZBI, Set-Get-Do, Mirror, and WML for more information.
Note • Do not use the same hex value for the control, format, and
delimiter character. The printer must see different characters to
work properly.
Default Value: 2C ,
Range: 00 to FF
To change the value shown:
1. Press MINUS (-) to move to the next digit position.
2. Press PLUS (+) to increase the value of the digit.
Table 8 • Printer Parameters (Sheet 14 of 22)
Language/Parameter
Action/Explanation
- User Guide 1
- Part Number: P1009874-003 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Bubbledot ICG font 11
- SETUP/EXIT button 12
- CALIBRATE button 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- Printer Setup 17
- Before You Begin 18
- Handling the Printer 19
- Select a Site for the Printer 20
- I) may damage the 21
- Interface 23
- Standard or 23
- Optional 23
- Description 23
- O) position 26
- Power Cord Specifications 27
- Types of Media 29
- Ribbon Overview 31
- Adhesive Test 32
- Ribbon Scratch Test 32
- Operations 33
- Media Paths 35
- Cutter Cutter 36
- Rewind Rewind (without 36
- Cutter option) 36
- Prepare the Media for Loading 37
- 110Xi4/R110Xi4 600 dpi 38
- Fanfold Media 40
- Load Media in Tear-Off Mode 42
- RIBBON OUT error 43
- Load Media in Peel-Off Mode 46
- Load Media in Cutter Mode 53
- Load Media in Rewind Mode 58
- If... Then 65
- Pull out the spindle hook 66
- Load Ribbon 67
- If… Then… 68
- 1) and under the 69
- Remove Used Ribbon 72
- Calibrate the Printer 74
- SENSOR PROFILE 75
- MEDIA AND RIBBON 75
- CALIBRATE 75
- Upper Media Sensor 76
- Lower Media Sensor 79
- Toggle Position Adjustment 80
- Printhead Pressure Adjustment 81
- Setup Mode 84
- Exit Setup Mode 85
- Default Password Value 86
- LIST SETUP 87
- LIST NETWORK 88
- WARNING REPLACE 95
- 3. Do you want to continue? 97
- To print a sensor profile: 98
- LOAD BACKING prompt displays 99
- RELOAD ALL displays 99
- Action/Explanation 100
- Configuration 101
- To change the value shown: 103
- Language/Parameter 103
- Error Condition 107
- Feed Label 107
- To skip these parameters: 108
- IDLE DISPLAY 109
- Routine Maintenance 113
- Replacing Printer Components 114
- Lubrication 114
- CLEAN HEAD NOW appears 115
- CLEAN HEAD NOW 116
- 1) counter-clockwise 117
- Clean the Sensors 119
- Transmissive Media Sensor 120
- Media Out Sensor Location 121
- Clean the Snap Plate 122
- RFID Printers 125
- Clean the Cutter 128
- Replace the Fuse 129
- Troubleshooting 131
- Troubleshooting Checklists 132
- LCD Error Messages 133
- LCD Display/ 134
- Printer Condition 134
- O) the printer 135
- I) the printer 135
- Print Quality Problems 139
- Note • A vertical drift of 141
- Calibration Problems 143
- NONE. See 144
- Ribbon Problems 145
- RFID TAG 146
- MEDIA POWER UP and 147
- O) and then back on (I) too 148
- LANGUAGE 149
- SAVE CHANGES in the 149
- Printer Diagnostics 151
- CANCEL Self Test 152
- PAUSE Self Test 153
- FEED Self Test 154
- Print Quality Description 156
- FEED and PAUSE Self Test 157
- Sensor Profile 159
- Specifications 161
- Features 162
- Bar Codes 163
- General Specifications 164
- Print Specifications by Model 165
- 140Xi4, 170Xi4, and 220Xi4 166
- Ribbon Specifications 167
- Media Specifications 168
- End User License 171
- Agreement 171
- End User License Agreement 172
- Glossary 177
- Numerics 181
Verwandte Produkte und Handbücher für Etikettendrucker Zebra 110Xi4
Etikettendrucker Zebra ZT420 Betriebsanweisung
(192 Seiten)
(192 Seiten)
Etikettendrucker Zebra LP 2824 Betriebsanweisung
(56 Seiten)
(56 Seiten)
Etikettendrucker Zebra R-2844Z Betriebsanweisung
(86 Seiten)
(86 Seiten)
Etikettendrucker Zebra GC420t Betriebsanweisung
(116 Seiten)
(116 Seiten)
Etikettendrucker Zebra ZM400 Betriebsanweisung
(116 Seiten)
(116 Seiten)
Etikettendrucker Zebra ZD500 Betriebsanweisung
(160 Seiten)
(160 Seiten)
Etikettendrucker Zebra ZT230 Betriebsanweisung
(18 Seiten)
(18 Seiten)
Etikettendrucker Zebra GC420d Betriebsanweisung
(100 Seiten)
(100 Seiten)
Etikettendrucker Zebra GX430D Betriebsanweisung
(128 Seiten)
(128 Seiten)
Etikettendrucker Zebra P110i Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Etikettendrucker Zebra P520i Bedienungsanleitung
(66 Seiten)
(66 Seiten)
Etikettendrucker Zebra T5206R Bedienungsanleitung
(394 Seiten)
(394 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern