Zebra Z4Mplus Bedienungsanleitung Seite 137
- Seite / 178
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
- User Guide 1
- Your Feedback Is Important 3
- Feedback Form 4
- Proprietary Statement 5
- FCC Compliance Statement 6
- Liability Disclaimer 6
- Limitation of Liability 6
- Copyrights 7
- DECLARATION OF CONFORMITY 9
- Warranty Information 11
- Printer Products 12
- Printhead Warranty Period 12
- Supplies Products 13
- Agreement 14
- Table of Contents 21
- Contents 25
- Contacts 26
- About this Document 27
- Document Conventions 28
- Related Documents 30
- Introduction 31
- Inspect the printer 32
- Front Panel 33
- Printer Side View 35
- Printer Setup 37
- Before You Begin 38
- Types of Media 40
- Continuous Media 41
- Print Mode 42
- Load Media and Ribbon 43
- Load the Ribbon 44
- Printhead Pressure Adjustment 46
- Set Printhead Pressure 47
- Rewind Media Alignment 48
- Configuration Label 49
- Basic Configuration 52
- Basic Configuration Process 53
- Position the Label Sensor 56
- Transmissive Sensor 58
- Communication 59
- System Considerations 60
- Cable Requirements 62
- Printer Basics 63
- Printer Overview 64
- Front Panel Keys 66
- Front Panel Lights 67
- Load Roll Media 68
- Cutter Mode 70
- Peel-Off Mode 72
- Liner Take-Up Mode 74
- Liner Slide Tab 76
- Liner Slide 76
- Liner Removal 79
- Rewind Mode 79
- PAUSE to enable printing 80
- Load Fanfold Media 82
- Bottom Feed 83
- Rear Feed 83
- Remove the Ribbon 86
- Leave the Setup Mode 90
- Configuration 100
- Selecting ZPL Mode 106
- Label Positioning Parameters 108
- SAVE SETTINGS 114
- PRINTER READY 114
- Routine Care and Adjustments 115
- Cleaning Procedures 116
- Clean the Exterior 117
- Clean the Interior 117
- Clean the Sensors 119
- Clean the Rewind Option 120
- Clean the Peel-Off Assembly 122
- Clean the Cutter Module 123
- Lubrication 124
- Fuse Replacement 125
- Troubleshooting 127
- Error Conditions 128
- Load Roll Media 129
- page 15) 129
- (page 64) and select 130
- Warnings 131
- Warning — CUTTER JAM 132
- OUT OF MEMORY* 132
- page 87 133
- Wrinkled ribbon 134
- Calibration 135
- Communication Problems 136
- Print Quality Problems 137
- Printer Diagnostics 138
- Cancel Self Test 139
- Pause Self Test 140
- Feed Self Test 141
- Loading Factory Defaults 142
- Specifications 143
- General Specifications 144
- Printing Specifications 145
- Media Specifications 146
- Ribbon Specifications 148
- °, 90°, 180°, 270°) 150
- Bar codes 151
- AC Power Cord 152
- DB-9 Connectors 153
- Serial Data Communications 154
- Cable Specifications 154
- (Printer) 157
- (Modem, etc.) 157
- Connector 159
- Parallel Data Port 161
- Memory Cards 165
- Extend Printhead Life 169
- Challenge 170
- Preventive Maintenance 171
- Save-a-Printhead 172
Verwandte Produkte und Handbücher für Etikettendrucker Zebra Z4Mplus
(86 Seiten)
(58 Seiten)
(22 Seiten)
(33 Seiten)
(102 Seiten)
(28 Seiten)
(57 Seiten)
(130 Seiten)
(62 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern