Zebra Stripe Betriebsanweisung Seite 36
- Seite / 150
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Printer Setup
Ribbon Overview
36
13290L-004 Rev. A S4M User Guide 6/15/09
Notes • ___________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Bubbledot ICG font 12
- POWER ALERT 13
- CANCEL FEED 13
- About This Document 14
- Document Conventions 14
- Introduction 15
- External View 16
- FEED FEED 18
- Appearance 19
- Control Panel Lights 20
- Printer Media Compartment 21
- Printer Language Modes 22
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- I) may damage the 28
- O) position 30
- Power Cord Specifications 31
- Types of Media 32
- Ribbon Overview 34
- Adhesive Test 35
- Ribbon Scratch Test 35
- Operations 37
- Media Paths 38
- Start a Roll of Media 39
- Insert Media into the Printer 40
- Fanfold Media 41
- Load Media in Tear-Off Mode 42
- 4. Slide out the media guide 43
- Close the printhead assembly 44
- Load Media in Peel-Off Mode 45
- Slide out the media guide 46
- PAUSE to enable printing 49
- Load Media in Cutter Mode 50
- Load Ribbon 53
- Remove Used Ribbon 57
- Calibrate the Printer 58
- Adjust the Reflective Sensor 59
- Adjust Printhead Pressure 61
- If the media... Then 62
- Configuration 63
- Setup Mode 64
- If you wish to... Then 65
- PASSWORD and the number 0000 66
- Printing Configuration Labels 68
- SETTINGS 69
- NETWORK 70
- Select a Display Language 71
- DARKNESS 72
- TEAR OFF 73
- LABEL TOP 73
- X FORMS ADJUST 73
- LEFT POSITION 73
- Y FORMS ADJUST 73
- MEDIA TYPE 74
- SENSOR SELECT 74
- PRINT SPEED 75
- PRINT WIDTH 75
- KDU MODE 75
- COMPAT. MODE 75
- CONTROL CODES 76
- RESOLUTION 76
- Password Level 3 Parameters 77
- MODULE A 78
- MODULE B 78
- PARALLEL COMM 78
- PRINT PAGE 78
- PRINT FORMAT 78
- DATA BITS 79
- STATUS RESPONSE 79
- HOST HANDSHAKE 80
- CONTROL CHAR 80
- COMMAND CHAR 80
- DELIM. CHAR 81
- REPRINT MODE 81
- CHANGE RTC DATE 81
- Control Panel Parameters 82
- ZPL OVERRIDE 83
- SENSOR PROFILE 84
- Parameter Explanation 85
- To modify this parameter: 86
- Routine Maintenance 87
- Replacing Printer Components 88
- Lubrication 88
- Clean the Exterior 89
- Cleaning Procedures 90
- Clean the Peel Assembly 94
- Close the media door 96
- Clean the Cutter Module 97
- Troubleshooting Checklists 100
- RIBBON OUT 101
- O) the printer 102
- I) the printer 102
- HEAD COLD 103
- HEAD TOO HOT 103
- DEFRAGMENTING 104
- ERROR CONDITION 104
- CUTTER JAM 104
- HEAD ELE. BAD 104
- Memory Errors 105
- Print Quality Problems 106
- Troubleshooting 107
- Note • A vertical drift of 108
- Calibration Problems 109
- Communications Problems 110
- YES, the printer 111
- O) and then on (I) 112
- O) and then 112
- Printer Diagnostics 114
- CANCEL Self Test 115
- PAUSE Self Test 116
- FEED Self Test 117
- Print Quality Description 118
- FEED and PAUSE Self Test 120
- Sensor Profile 122
- Specifications 125
- General Specifications 126
- Agency Approvals 127
- Printing Specifications 128
- Media Specifications 129
- Ribbon Specifications 130
- ZPL II Commands 131
- Define Password 132
- End User License 133
- Agreement 133
- End User License Agreement 134
- Glossary 139
- Cutter Jam message, 104 144
- HEAD COLD message 145
- HEAD ELEMENT BAD message, 102 145
- HEAD TOO HOT message, 103 145
- RIBBON IN message, 102 146
- THERMISTOR FAULT message 147
Verwandte Produkte und Handbücher für Etikettendrucker Zebra Stripe
Etikettendrucker Zebra S400 Betriebsanweisung
(146 Seiten)
(146 Seiten)
Etikettendrucker Zebra TTPM2 Spezifikationen
(102 Seiten)
(102 Seiten)
Etikettendrucker Zebra A300 Betriebsanweisung
(38 Seiten)
(38 Seiten)
Etikettendrucker Zebra 105SL Spezifikationen
(246 Seiten)
(246 Seiten)
Etikettendrucker Zebra A300 Betriebsanweisung
(36 Seiten)
(36 Seiten)
Etikettendrucker Zebra S400 Bedienungsanleitung
(46 Seiten)
(46 Seiten)
Etikettendrucker Zebra S4M Spezifikationen
(404 Seiten)
(404 Seiten)
Etikettendrucker Zebra Z6M Bedienungsanleitung
(112 Seiten)
(112 Seiten)
Etikettendrucker Zebra XiIIIPlus Bedienungsanleitung
(152 Seiten)
(152 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern