Zebra 2746e Wartungshandbuch PDF herunterladen (Seite 13)

REQUIRED TOOLS

Make use of the following tools while performing replacement procedures:

Torque wrench with 1/4" hex receptacle)

Phillips driver #1 (tip for 1/4" hex receptacle)

Phillips driver #2 (tip for 1/4" hex receptacle)

Allen key socket tip drivers (tip for 1/4" hex receptacle);

sizes: 1/16", 5/64", 3/32", 1/8", 3mm, 4mm

Nut driver, sizes: 7mm, 8mm, 1/4"

Flat Blade screwdriver (small)

needle-nose pliers

pliers for E-ring retainers (12R)

pliers for axial retainers

tweezers

Clutch torque bit (and torque gauge are spare 105902-060)

.005" shim

Loctite 222 thread locker or equivalent

980428-001 Rev. A 9

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 85 86

Commercial 1
Thermal Printers 1
Service Manual 1
FOREWORD 2
TECHNICAL SUPPORT 2
COPYRIGHT NOTICE 2
TRADEMARKS 2
INTRODUCTION 5
Conventions 7
4 980428-001 Rev. A 8
TROUBLESHOOTING GUIDE 9
(Full-On Print Pattern) 12
REQUIRED TOOLS 13
10 980428-001 Rev. A 14
REPLACING PARTS 15
Installation 16
Exterior Cover 16
Preparations 16
Disconnect Sensor 17
Cable at JP26 17
Printhead 20
Cut Cable Ties 21
Set AC Voltage 23
Set Voltage 23
Re-assemble Printer 23
DC Voltage Verification 24
DC Voltage adjustment 24
Switch and AC 25
Power Inlet Module 25
Retaining Tabs 25
DC Power Cable 26
AC Power Cable 27
Removal & Replacement 27
Securing the Wire Harness 28
Control Panel Tie Point 29
Anchor Tie 30
Final Check 31
Main PCBA 32
RTC Installation 34
Re-assembling the Printer 34
Motor Cable 35
Printhead Cable 37
Pin 1 of JP21 38
Connector 38
Label Guide & Sensor 39
Release Latch 40
Label Sensor PCBAs 42
Control Panel 45
Head-up Sensor 47
Label Taken Sensor 49
Peel Mechanism 51
Label Guide Tab 52
Ribbon Pulley (60 tooth) 54
Ribbon Drive Belt 55
Platen Belt (120 tooth) 56
Ribbon Collar & Spring 57
Lower Print Mechanism 64
Printhead Carriage 66
Cutter Cable 68
Instructions 70
Printer Configuration Check 71
Checking the Installation 71
Max. Allowable 72
Deflection = .125" 72
Measuring Tension 73
Verify Tension 73
Tension Adjustment 74
Ribbon Path Adjustment 75
Presetting 75
Adjusting the Ribbon Path 75
Vertical Slot Ad 76
Resetting the printhead 78
Packaging for Shipment 79
Printer Preparation 79
Packaging the Printer 79
Unpacking Instructions 80
CLEANING AND MAINTENANCE 81
Preventive Maintenance 82
Basic Cleaning 82
Cleaning the Media Path 83
Cleaning the printhead 83
Cleaning Film Usage Issues 84
RECOMMENDED SERVICE 85
82 980428-001 Rev. A 86

Kommentare zu diesen Handbüchern

Keine Kommentare

Zebra 2746e Wartungshandbuch Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drucken & Scannen Zebra 2746e